Cheetah1 SDK v1.16 Known Issue - Revision history

HuangKun at 01:33, 31 October 2018

2018-10-31T01:33:45Z

HuangKun at 02:30, 30 October 2018

2018-10-30T02:30:00Z

HuangKun at 02:29, 30 October 2018

2018-10-30T02:29:33Z

HuangKun at 02:06, 30 October 2018

2018-10-30T02:06:44Z

64.64.108.60: 创建页面，内容为“Cheetah1

'''1. 不支持常见的串口波特率38400。下一版本会支持。'''
有一个补丁可以增加。
\\192.168.1.88\RoseekShare\RO…”

2018-08-29T05:19:49Z

创建页面，内容为“Cheetah1 '''1. 不支持常见的串口波特率38400。下一版本会支持。''' 有一个补丁可以增加。 \\192.168.1.88\RoseekShare\RO…”

New page

Cheetah1 
 
'''1. 不支持常见的串口波特率38400。下一版本会支持。''' 
有一个补丁可以增加。 
\\192.168.1.88\RoseekShare\ROSEEK_WebUseFullSDK\Cheetah1_cn\v1.16.00_20170712_patch_1

'''2. Roseek_MediaEncoder_InitParamsV1 函数在文档中没有。''' 
该函数使用新的参数数据结构，增加了一些配置项。 
暂时这些配置项还未启用，因此不需要额外配置。 
可以沿用Roseek_MediaEncoder_InitParams，或者使用
Roseek_MediaEncoder_InitParamsV1，效果是一样的。 

'''3. Linux 串口启动时不能马上使用，过大约1分钟之后才能使用''' 
回答： 
当前及之前的版本我们发现有个服务会影响串口 
建议您手动把这个服务配置为关闭。命令为： 
sudo systemctl disable ModemManager.service 
1.17版本SDK会在安装时自动执行这个命令以修正这个问题。

@@ Line 16: / Line 16: @@
 It is recommended that you manually configure this service to be down. <br/>
 The command is:<br/>
-	sudo systemctl disable ModemManager.service<br/>
+:sudo systemctl disable ModemManager.service<br/>
 The 1.17 version of the SDK will automatically execute this command during installation to fix this problem.<br/>

@@ Line 14: / Line 14: @@
 '''3. The Linux serial port cannot be used immediately when it is started. It takes about 1 minute to use.'''<br/>
 In current and previous versions, we found that a service can affects the serial port.<br/>
-It is recommended that you manually configure this service to be down. The command is:<br/>
+It is recommended that you manually configure this service to be down. <br/>
 	sudo systemctl disable ModemManager.service<br/>
 The 1.17 version of the SDK will automatically execute this command during installation to fix this problem.<br/>

@@ Line 6: / Line 6: @@
-'''2. The Roseek_MediaEncoder_InitParamsV1 fuction is not in the document.'''<br/>
+'''2. The "Roseek_MediaEncoder_InitParamsV1" function is not in the document.'''<br/>
 This function uses a new parameter data structure and adds some configuration items.<br/>
 Temporarily, these configuration items are not enabled, so there is no need to additional configuration.<br/>
-You can use the Roseek_MediaEncoder_InitParams or use the Roseek_MediaEncoder_InitParamsV1, the effect is the same.<br/>
+You can use the "Roseek_MediaEncoder_InitParams" or use the "Roseek_MediaEncoder_InitParamsV1", the effect is the same.<br/>